ARRL FMT: operator checklist
WSJT-X FreqCal + FMT Assistant · November 13, 2026 UTC (evening of November 12 in North America)
Page 1: steps 1 and 2, before the night
Page 2: steps 3 and 4, on the night
CallRadio
AntennaUTC offset
Step 1: Set up (a few days before)
WSJT-X
- WSJT-X Settings > Frequencies: calibration intercept 0 and slope 0 ppm. FMT Assistant applies the correction itself.
- WSJT-X FreqCal frequency list has the WWV/WWVH frequencies you can hear.
FMT Assistant, tab 1 Setup & radio
- Latest version downloaded. Callsign entered; WSJT-X log folder chosen (WSJT-X File > Open log directory); the WSJT-X panel shows no errors.
- Frequency reference set (a FlexRadio reports its own). GPS-locked: the top right reads GPSDO locked and the Calibration tab is on No correction; any other radio: Average.
- Schedule (UTC) checked against the ARRL FMT page (fmt.arrl.org) and the fmt-nuts group.
- Voice prompts tested (Test button), volume set.
- FlexRadio users (optional): radio found, slice chosen, Set radio tested.
- Windows clock synchronised (Settings > Time > Sync now).
Step 2: Practice (at least once)
- Optional: a WWV calibration on the Practice calibration card (practice only; skip it with a GPS-locked radio).
- One full practice run on tab 2 Practice (a local AM station or WWV): Start a fresh fmt.all ticked, set the dial, centre the tone near 1500 Hz, type the exact dial, measure, Capture, read the answer.
- Readings steady: SD a few hundredths to a few tenths of a hertz.
Audio recording (recommended)
- A separate recorder is set up to record the receiver audio for the whole evening, for example Audacity recording the same input WSJT-X uses (DAX on a Flex).
- Test recording made and played back.
WSJT-X won't record it for you. In FreqCal mode WSJT-X writes only fmt.all; it does not save .wav files, even with Save > Save all on. Use another program if you want the audio.
Step 3 begins: on the night, before 02:09 UTC
- Radio on and warmed up (an hour or more is best); don't change radio settings from here to the end.
- WSJT-X and FMT Assistant open; tab 3 Test night showing; voice on.
- GPS-locked radio: the reference reads locked.
- Problems (top right) reads No problems (or each one understood).
- Old fmt.all deleted (WSJT-X File > Open log directory), so earlier readings can't mix in.
- Audio recorder started, with enough disk space for about 90 minutes.
- Receive mode USB (DIGU on a Flex), RIT off, no DIGU offset.
- Pen and this sheet ready to write each dial down as a backup.
- Phone or other noise sources away from the radio.
Every Capture also saves a dated copy in the session's Archive folder that is never overwritten, so every file from the night is kept (Open session folder on tab 4 Results).
Step 3: Test night, minute by minute
FMT Assistant speaks each step. Tick each box as you go. Write your local time in the Local column.
| UTC | Local | Do this | |
| 02:09 | | Calibration before (WWV) |
| 02:09 | | WSJT-X Mode > FreqCal, Measure on, Tools > Execute frequency calibration cycle on. Let it run several cycles. | |
| 02:25 | | Cycle off; Capture Calibration before; check the Calibration tab (GPS-locked: a check only). Don't click Apply in Solve. | |
| Run | Call-up | Key-down | Station | Nominal | Dial to set (USB) |
| 1 | 02:29 | 02:34 | W8RKO 40 m | 7064 kHz | 7062.500 kHz |
| 2 | 02:44 | 02:49 | K5CM 40 m | 7065 kHz | 7063.500 kHz |
| 3 | 02:59 | 03:04 | W8RKO 80 m | 3598 kHz | 3596.500 kHz |
| 4 | 03:14 | 03:19 | K5CM 80 m | 3599 kHz | 3597.500 kHz |
For each run (repeat four times)
| When | Do this | 1 | 2 | 3 | 4 |
| Call-up −5:00 | Calibration cycle off, only Measure on. Set the USB dial (Flex: Set radio). | | | | |
| −2:00 | Carrier near 1500 Hz on the waterfall? If not, Tone is at… and retune. Type the exact dial into the app and write it below. | | | | |
| −0:30 | Hands off the dial. | | | | |
| Key-down | One minute of carrier. Let WSJT-X measure the whole minute. Watch the run's Live preview: readings arriving, the chart steady, no amber warnings. | | | | |
| +1:00 | Press Capture for this run (a dated copy goes to Archive). Check the dial entry, and that the run shows Ready. | | | | |
| 03:21 | | Calibration after (WWV) |
| 03:21 | | Back to WWV: Measure on, calibration cycle on. Several cycles, then cycle off and Capture for Calibration after. | |
| After | | Stop the audio recorder and save the recording with the date and your call in its name. | |
| Step 4 | | Tab 4 Results: every run Ready; Save report & show; enter each Carrier frequency at fmt.arrl.org/fmtentry.php. | |
| After | | Back up the session folder (with its Archive folder) and the audio recording. When the results are published, type them into How close were you? on tab 4. | |
Paper backup
| Run | Station | Exact dial used | Mean fMeas | Carrier frequency submitted |
| 1 | W8RKO 40 m | | | |
| 2 | K5CM 40 m | | | |
| 3 | W8RKO 80 m | | | |
| 4 | K5CM 80 m | | | |